YJS-601 carbon fiber plastic YJS-601 carbon fiber plastic for solvent-modified epoxy adhesive. Part A: B = 3: 1. ? ★ product uses mainly for CFRP. The product of the carbon fiber has a strong permeability, high tensile bond strength and connection strength; resistant to corrosion and wear, with high durability and excellent mechanical properties. Technical Specifications: Conforms to GB50367-2006 standard technical requirements. ? Performance Project test results the performance requirements (A-level) colloidal properties Tensile strength (MPa) 43.4 ≥40 tensile modulus of elasticity (MPa) 2527 ≥2500 elongation (%) 1.86 ≥1.5 compressive strength (MPa) 74.5 ≥ 70 flexural strength (MPa) 53.3 ≥50, and shall not brittle (fracture-like) bonding capacity sabotage steel - steel tensile shear strength of the standard value (Mpa) 14.6 ≥14 positive and concrete tensile bond strength (Mpa ) 3.24, and for concrete cohesion destruction ≥2.5, and for concrete cohesion destruction ★ use of methods and precautions 1 ,? the YJS-601 carbon fiber impregnated plastic Part A and Part B at 3:? 1 ratio, Stir to use. YJS-601 glue should ,? after mixing two (depending on the ambient temperature) used within 60 ~ 90min completed. 3 ,? The product density of about 1.15 ~ 1.25g / cm3 (cured product), the gel time of about 3 to 6 hours. ★ storage and transport of a product can be stored at ambient temperatures below 40 ℃, the shelf life of 24 months. 2, the product is solvent, should be stored away from open flame, heating devices. ★ Packing:? 18kg + 6kg / group 9 + 3KG / group bonded carbon fiber reinforced construction ★ Description Construction conditions:? (1) construction of the surface should be clean and dry. (2) Construction of the temperature should be greater than 15 ℃, less than 40 ℃. (3) non-rainy outdoor construction. (4) more than 85% relative humidity or concrete surface exposed occasions, do not allow the construction. Construction Technology: 1, the primary requirements: the adhesive surface must be flat, solid, free of impurities, repair glue has hardened, and the surface is dry, there is no dew, frost and so on. 2, tune ??? glue: Calculate the amount in accordance with the bond area, accurately weighed A and Part B, in a clean container, stir. Good tune glue should apply during the run. 3, brushing primer: proportionally mixing of YJS-602 carbon fiber bottom brushing glue directly onto the concrete base, with plastic concrete surface should be full. After hardening the next process. 4. Paste the carbon fiber: ① with a stiff brush will be tuned YJS-601 impregnated plastic bonded to the surface evenly brushing glue full amount must be sufficient. Brushing about 600-800g / m2. ② will cut a good carbon fiber cloth affixed to the surface of the concrete paste, use a hard rubber or plastic scraper stick rolling back and forth, to promote carbon fiber straight, extended, full penetration of the adhesive. CFRP long length should take up joint 10-20㎜. ③ brushing the surface of the carbon fiber part adhesive, continue rolling back and forth scratch, expelled bubbles, and the adhesive evenly cover CFRP. Brushing is about 200g / m. ④ stand for 1-2 hours to refer to dry and repeat rolling eliminate or offset the carbon fiber float may cause bubbles, bonding is not real and so on. ⑤ multi-sticky, repeat the above operation. ⑥ After curing of the adhesive, is pasted on the carbon fiber surface and then a layer of glue scratch. Note: 1, ?? with plastic, should be carried out under proper ventilation. 2, ?? operator to use safety glasses, wear protective masks. 3, ?? rain, frost and fog weather for outdoor construction not. 4, ?? Carbon fiber is conductive fiber, therefore, must stay away from the construction of operating power to avoid electric shock casualties. Outdoors near a charged body (wires, etc.) during the construction, if the wind should stop the construction, in order to avoid the wind blowing CFRP contact conductor and accidents. 5, ?? CFRP unidirectional fiber direction, the index unit weight, thickness, tensile strength, elastic modulus, etc. must comply with the relevant requirements. All our products are state detection chamber testing. All our products are qualified, after no worries! At the same time I have a professional technical staff free of charge for customers to solve all engineering problems, problems, etc.